Auxiliary Equipment

Drying Equipment

Rotary Kiln Dryer

Heat Source

Browse by application

Build an customized solution that fits your requirement

Biomass Pellet Plant

【Application】:Agriculture and forestry waste,Groundnut-shell,Sugarcane Biogases,Caster Shells/Stalk ,Sawdust,Coffee Husk,Paddy Straw and others.

【Moisture Content】:10-15%.
【Raw Materials】:lower than 10 mm.

Biomass Pellet Plant Production Lines Flowcharts:
Biomass Pellet Plant/Wood Pellet Plant:
Biomass drying and pelleting line is the process of making waste biomass materials into solid fuel. The objects are used for burning purposes.Biomass Pellet is one of the most commonly used pelletizing materials.
Biomass Pellet can be made from any type of Agriculture and forestry waste:
Groundnut-shell • Sugarcane Biogases • Caster Shells/Stalk • Saw dust • Coffee Husk • Paddy Straw • Sunflower Stalk • Cotton Stalks • Tobacco waste • Mustard Stalk • Jute waste • Bamboo Dust • Tea waste • Wheat Straw • Palm husk • Soybeans husk • Coir Pitch Barks/Straws • Rice Husks • Forestry wastes • Wood Chips and many other Agro wastes.The raw material moisture Content Should be Less than 12%, grain size is below 5*5mm.
(1). Crushing Process:
When the thickness of raw wood material is >10mm, and >50 * 50mm(L * W), that need use the Wood Chipper to chip them into small pieces, then crush the small pieces into wood powder with diameter less than 3mm by Hammer Mill (Crusher).
(2). Drying Process:
The best moisture content to pelletize is about 13-15%. Our Rotary Dryer is made up of Stove and Main Rotary Dryer, which can reduce the moisture from 60% to 10%. Our stove is fueled by sawdust, wasted wood, coal, which can save electricity consumption largely. Our Rotary Dryer is specially designed for energy saving purpose, the outside of the dryer is covered with special cotton material sheet to prevent the heat from outrunning.


(3). Pelletizing Process:
MZLH Wood Pellet Line is a most important equipment, which have the following features:
The lubrication system for wood pellet lines adopt the tracing and inspecting system controlled by the microcomputer. When the temperature of the bearing is over the normal temperature, the microcomputer will start the Auto-Lubrication System to lubricate the bearings, which completely solve the trouble of lubricating roller depending on the operation experience. The Lubrication System is made up of the tracing and inspecting system controlled by the microcomputer, auto-lubricating system on time and compelled lubricating system by hand.

Driving Gear adopts the high precision gear transmission structure. The wear bearing is SKF from Sweden. The ring die adopts the hoop fastening method, which is increasing the speed of discharge comparing with the past bolt fastening method. As a result, the capacity is 10-15% higher than the belt transmission structure.

As per the wood pelletizing plant ring die and roller of the wood pellet line, we have the fine machining with the alloyed steel. And our heating treatment is also different from the other domestic manufacturers. Our carburizing treatment make the depth of hard facing to 2mm, which improve the anti-abrasion of the ring die and roller more than 10 times, and it can save the production cost heavily.

Model
DLKL1000
DLKL1500 DLKL2000 DLKL3000 DLKL5000
capacity(t/h)
0.8-1.0
1.2-1.5
1.5-2.0
2.5-3.0
4.5-5.0
motor power(kw)
135
175
210
255
300
weight(ton)
45
47
55
68
73
area(m2

10×24m

10×24m
10×24m
12×26m
12×26m

 

Please enter your demand such as Raw material type,Capacity, Self introduction, Required specifications. To become our quality clients will have access to a 3% discount of contract!

You can also send email to service@tdaxy.com

service@tdaxy.com|Product|Productiong Line|News|Purchase|Service

2015 Copyright Zhengzhou Taida Drying Equipment Co.,Ltd.